Skip to main content

Standby generator installs for Dallas homes and businesses through an independent, licensed installer

Outage Ready GeneratorsGet Installation Quote

Generator Repair and Maintenance in Dallas

Most standby generators spend nearly all their life waiting. That is exactly why they fail: oil ages, batteries weaken, and wasps or mice move into the enclosure while nobody is looking.

Outage Ready Generators connects Dallas owners of Generac and other brands with independent, licensed electrical contractors who handle annual maintenance and repairs. Tell us the brand, the size if you know it, and what the unit is doing or not doing. A local pro diagnoses the problem on site and quotes the fix before any work starts.

Get Installation Quote Our service area

Get an installation quote

We send your request to one independent, licensed installer. Asking is free. How referrals work

Standby generator on a concrete pad beside a brick home

Signs your generator needs attention

  • It did not start during the last outage, or it started and then shut down.
  • A warning light or fault code shows on the controller.
  • The scheduled self-test run did not happen, or it sounds rough.
  • You see oil or fuel under the unit, chewed wires or nests inside the case.
  • The battery terminals are crusted or the battery is more than a few years old.
  • It has been more than a year since anyone serviced it.
  • It ran for days in a long outage. Generac publishes separate steps for units after extended running.

What annual maintenance covers

Generac's home standby guidance tells owners to follow the schedule in their model's owner's manual. The routine tasks it lists include:

  • Oil and oil filter. Change on schedule. Old oil is a common reason for engine wear.
  • Air filter. Check and replace when dirty.
  • Spark plugs. Inspect and replace as needed.
  • Battery. Check voltage and clean any corrosion on the contacts.

A pro also looks for leaks, checks the gas connection, clears debris from the vents and runs the unit through the transfer switch. Angi recommends professional maintenance once a year, with owners doing simple visual checks in between.

Timing service around Dallas weather

North Texas puts two hard seasons on a generator. Summer heat stresses batteries and cooling systems, and a winter outage can mean days of steady running in the cold, as February 2021 showed. Many owners book the annual visit in early fall so the unit is fresh before freezing weather, then have it checked again after any long outage.

Between visits, a quick look once a month helps:

  • Is the controller showing a ready status, with no fault lights?
  • Is the area around the case clear of leaves, mulch, toys and grass clippings?
  • Are there signs of insects or rodents at the vents?
  • Did the scheduled exercise run happen? Many owners hear it from inside.

Write down any fault codes before you request a visit. The pro can often order the likely part before arriving.

How a repair visit goes

  1. Request. Use the form with the brand, model if known and the symptoms.
  2. Diagnosis. The pro reads fault codes, tests the battery and checks fuel, ignition and the controller.
  3. Written quote. You see the parts, labor and price before work starts.
  4. Repair. Common fixes include batteries, voltage regulators, carburetors and transfer switch parts.
  5. Test. The unit runs under load and the switch transfers and returns, so you know it works.

Repair and maintenance costs

ItemReported rangeSource
Whole-house maintenance visit$172 to $395 (about $273 on average)Angi
Yearly upkeep total$200 to $600Angi
Maker service contract, per year$150 to $300Angi
Transfer switch repair$50 to $150Angi
Transfer switch replacement part$200 to $400 plus laborAngi
Voltage regulator partup to about $80 plus laborAngi
Carburetor replacement$60 to $500Angi
Stator and rotor$250 to $1,500Angi
Engine repair$50 to $2,000Angi

If repairs keep stacking up on an older unit, ask the pro to price a replacement too. The generator installation cost page helps you compare.

What to ask the technician

  • Are you trained on my brand, and can you get parts locally?
  • Is this a one-time fix, or a sign of a bigger problem?
  • Does the repair affect my manufacturer warranty?
  • Do you offer a yearly service plan, and what does it include?
  • Is your electrical contractor license active on the TDLR electricians site?

If the unit keeps tripping under load, the problem may be sizing, not parts. Read generator sizing. If the switch is the culprit, see transfer switch installation.

Areas we cover for generator repair and maintenance

Generator questions

Why did my generator not start during the outage?

A weak or dead battery is a frequent cause. Others include low oil shutdowns, a fault code, a closed gas valve, a failed starter or a transfer switch that never sent the start signal. A technician reads the controller first.

Can I do generator maintenance myself?

Generac says owners who are comfortable can do routine tasks with a maintenance kit and the right tools. Gas and electrical repairs are a different matter and belong with a licensed pro.

Will you send someone to service a unit I bought elsewhere?

Yes. Where you bought it does not matter. The pro we match you with services the brand you own, Generac or another make.

Is it worth fixing a ten-year-old generator?

It can be if the engine is sound and parts are available. When the quote approaches the price of a new unit, a replacement with a fresh warranty may make more sense. Ask for both prices.